Satel SATELLINE-M3-R3 Betriebsanweisung Seite 1

!WIRELESS WORLD – LOCAL SOLUTION !!!!!!!!!!!!!!SATELLINE®-M3-R3 RADIO RECEIVER MODULE USER GUIDE Version 1.2

SATELLINE-M3-R3 User Guide, Version 1.2 9 Pin numbering of 1.27 mm pitch DTE connector. View from top side of unit 1.4 Pin order of the DTE

SATELLINE-M3-R3 User Guide, Version 1.2 10 Pull low / drive low to set UART1 (RD1,TD1) into known state. See separate section of manual. 18

SATELLINE-M3-R3 User Guide, Version 1.2 11 2 MECHANICAL CONSIDERATIONS 2.1 Fixing device to host The radio module can be mounted on to th

SATELLINE-M3-R3 User Guide, Version 1.2 12 Picture. The two different standoffs in a close-up. Picture . Open and closed standoff. Screw

SATELLINE-M3-R3 User Guide, Version 1.2 13 2.3 Soldering / host board instructions for mounting pegs 20,002,03,020,003,0Drill pattern 34,8M

SATELLINE-M3-R3 User Guide, Version 1.2 14 3 CHANGING PARAMETERS USING SL-COMMANDS The controlling terminal device can change the configura

SATELLINE-M3-R3 User Guide, Version 1.2 15 PS-mode Receiver ON/OFF 1. When started, 7 messages are analyzed and the average is calculated. T

SATELLINE-M3-R3 User Guide, Version 1.2 16 3.5 Turn ON using command When being in either off or sleep mode, the modem will be automaticall

SATELLINE-M3-R3 User Guide, Version 1.2 17 3.9 Startup sequence The following diagram will describe the startup sequence. VCC_IOENA_MODEM

SATELLINE-M3-R3 User Guide, Version 1.2 18 3.10 Shutdown sequence The following diagram will describe the shutdown sequence. VCC_IOENA_MODEM

SATELLINE-M3-R3 User Guide, Version 1.2 1 IMPORTANT NOTICE All rights to this manual are owned solely by SATEL OY (referred to in this user

SATELLINE-M3-R3 User Guide, Version 1.2 19 3.11 Time parameters for start-up and shutdown sequences Parameter Min time Recom. Time (* Expl

SATELLINE-M3-R3 User Guide, Version 1.2 20 3.12 Stat pin The STAT pin indicates the status of the device. It can be used to drive a LED usin

SATELLINE-M3-R3 User Guide, Version 1.2 21 4 TECHNICAL SPECIFICATIONS SATELLINE-M3-R3 complies with the following international standards:

SATELLINE-M3-R3 User Guide, Version 1.2 22 GENERAL Operating Voltage 4.0 VDC Temperature Range -25°C...+55°C. Type approval condition Temp

SATELLINE-M3-R3 User Guide, Version 1.2 23 4.2 DC electrical specifications Over recommended operating conditions Parameter Condition Min M

SATELLINE-M3-R3 User Guide, Version 1.2 24 5 DEFAULT DELIVERY VALUES DEFAULT VALUES OF THE ADJUSTABLE SETTINGS ( the user can change thes

SATELLINE-M3-R3 User Guide, Version 1.2 25 6 CONSIDERATIONS 6.1 Emi Interferers The module is designed to be mounted inside a host device.

SATELLINE-M3-R3 User Guide, Version 1.2 26 6.2 Electrostatic discharge As the module is intended to be embedded in a host application, in

SATELLINE-M3-R3 User Guide, Version 1.2 2 RESTRICTIONS ON USE SATELLINE-M3-R3 radio modem module has been designed to operate on frequency

SATELLINE-M3-R3 User Guide, Version 1.2 3 PRODUCT CONFORMITY Hereby, SATEL Oy declares that SATELLINE-M3-R3 radio modem module is in complia

SATELLINE-M3-R3 User Guide, Version 1.2 4 WARRANTY AND SAFETY INSTRUCTIONS Read these safety instructions carefully before using the product

SATELLINE-M3-R3 User Guide, Version 1.2 5 TABLE OF CONTENTS IMPORTANT NOTICE ...

SATELLINE-M3-R3 User Guide, Version 1.2 6 3.8 Restart ...

SATELLINE-M3-R3 User Guide, Version 1.2 7 1. INTRODUCTION SATEL OY is a Finnish electronics and Telecommunications Company specialising in t

SATELLINE-M3-R3 User Guide, Version 1.2 8 1.3 DTE connector DTE connector is 20-pin pass-through connector. This connector allows the pin t